Oxy-acetylene torches have been a staple in the maritime industry for many decades and are used for metal cutting, welding, brazing, and heating during onboard maintenance. When purchasing gas welding and cutting equipment, one often overlooked aspect is ensuring that the equipment meets technical specifications for safety and compliance, reports Wilhelmsen.
Gas welding and cutting safety
Despite close attention paid to gas welding and cutting safety, there are still too many cases of personnel being injured or even killed due to the use of poor or substandard quality equipment. There have been incidents where flashback into acetylene cylinders has triggered decomposition of the gas causing the cylinder to explode. In one case, a cylinder exploded only three minutes after a flashback with devastating results. Fortunately, no one was injured because the operator realized that the cylinder was in a dangerous condition, raised the alarm and the location was evacuated (Reference: AIGA Safety Bulletin 01/05).
Protecting against flashbacks during hot work is in line with the International Safety Management (ISM) Code and the Maritime Labour Convention (MLC) 2006, under which ship owners and operators are obliged to do their utmost to safeguard the occupational health and safety of personnel and prevent accidents both at sea and in ports.
Awareness is everything in ensuring the right behavior. In a recent Welding Safety Inspection (WSI), for instance, our inspector discovered that flashback arrestors were missing from the gas welding and cutting equipment, where the consequences in the event of a flashback accident could be severe and disastrous. A strong safety culture and the right mindset among crew members are essential for reducing safety risks.
Flashbacks explained
Under correct conditions, where there is a balance between the gas mix exit velocity (i.e., speed of the gas out of the nozzle) and the combustion velocity (i.e., burning speed of the gas), the gas will burn correctly in a stable manner. A flashback will occur if the combustion velocity exceeds the gas mix exit velocity, with the flame burning into the equipment. Flashbacks typically occur at the cutting nozzle or welding attachment tip (orifice) of the torch setup.
What to do in the unlikely event of a flashback
Acetylene is extremely flammable, and unstable and under certain conditions can decompose explosively into its constituent elements, carbon and hydrogen. A flashback can trigger decomposition in the acetylene cylinder. Therefore, it is crucial to keep the cylinder on the uppermost continuous deck and ensure direct access to the open deck. This allows for easy removal in case of an emergency. Never keep cylinders inside the hull. Note that UnitorTM acetylene cylinders are designed in line with international standards, incorporating features that allow for safe filling and storage of acetylene gas, and retard any acetylene decomposition should it occur, providing enough time for emergency actions to be taken.
If a flashback occurs and it is safe to do so, immediately close both acetylene and oxygen cylinder valves. The flame should go out when the acetylene is shut off. If the flame cannot be extinguished at once, evacuate the area. It is important to keep mittens or gloves in a convenient location near the gas cylinder. The mittens or gloves should be made from flame-retardant material and can be used on either hand to close the top valve of an acetylene cylinder that is on fire.
Carefully check the cylinder and any other acetylene cylinders that may have been affected by fire or flames. If the cylinder becomes more than hand warm (60-70°C) or starts to vibrate, evacuate the location immediately. Do not attempt to move an unstable cylinder; moving it could restart or accelerate the gas decomposition. It could be several days before it can be moved. Use the fire hose from a distance of at least 20m and hose down the cylinder body with a direct water spray. Cooling the cylinder down is the only way to stop decomposition.
Depending on the situation, throw the cylinder overboard.
What should you look for when purchasing flashback arrestors?
Despite welding equipment being a low investment priority versus, for example, fuel costs, it is important to embed the right behaviors among your personnel to decrease the likelihood of incidents. Safety is paramount.
Replace expired products (in terms of life expectancy, arrestors should be replaced every five years in line with OCIMF SIRE 2.0 or RightShip RISQ 2.0/3.0 requirements) and only purchase flashback arrestors manufactured to the ISO 5175-1 standard and that have BAM (Bundesanstalt für Materialforschung und -prüfung or German Federal Institute for Materials Research and Testing) certification and under-surveillance approvals.
The key selection criterion is to only buy flashback arrestors from a trusted source or reputable manufacturer with a good safety track record. Avoid buying second-hand units, incorrect type, or flashback arrestors with no local standards.
Wilhelmsen Ships Service (WSS) has been supplying high-quality Unitor gas equipment for decades with an excellent safety track record in the maritime industry. All flashback arrestors provide reliable protection against dangerous reverse gas flow and flashbacks according to EN ISO 5175-1. Our 85-10 series, S- 55, and W-66S products are BAM certified, while our basic FR-20 product conforms to EN ISO 5175-1 and are all manufactured by an industry-leading manufacturer and subjected to rigorous testing.
Did you subscribe to our daily Newsletter?
It’s Free! Click here to Subscribe
Source: Wilhelmsen
